APT Construction installs gutters and gutter guard systems for homeowners in Molalla who are dealing with water that spills over the roof edge, saturates the soil along the foundation, or washes out flower beds each time it rains. You may have noticed erosion channels forming in the gravel or mulch below the roofline, or water staining on the siding where runoff splashes back against the wall. This service includes installation of seamless aluminum gutters, downspout placement to direct water away from the structure, and gutter guard systems that prevent leaves and debris from blocking the flow, particularly important in areas with Douglas fir and oak cover common around Molalla.

The installation begins with measurement of the roofline to determine the length of each gutter run and the placement of inside and outside miters at corners. Gutter sections are cut and formed on site using a seamless gutter machine, eliminating joints where leaks typically develop. Hangers are fastened to the fascia board at intervals that prevent sagging under the weight of collected water, and the gutter is pitched slightly toward the downspout outlet to encourage drainage. Downspouts are attached with straps and routed to discharge at least six feet from the foundation, either onto splash blocks or into underground drains that carry water to a safe release point. In Molalla's wet season, a single storm can deliver several inches of rain, and without properly sized gutters, that volume overwhelms undersized systems and spills directly onto the foundation.

Reach out to schedule an assessment of your current drainage setup and receive recommendations for gutter sizing and guard options suited to your roof and landscape.

You will see that water no longer pours off the roof in sheets during heavy rain, and the soil around your foundation stays firm instead of turning into saturated mud. Flower beds and bark mulch remain in place rather than washing into the lawn, and the siding at ground level stays dry, preventing mold and rot in the lower courses. Gutter guards keep pine needles, moss fragments, and leaf debris out of the gutter channel, so water continues to flow freely even after weeks of autumn leaf drop. APT Construction sizes gutters to match the square footage of roof area draining into each section, ensuring the system can handle peak flow without overtopping.

Gutter guards are installed over the top of the gutter channel, allowing water to enter while blocking larger debris. Mesh and perforated covers are common options, selected based on the type of trees near the home and the roof pitch. Guards reduce the frequency of gutter cleaning but do not eliminate it entirely, as fine particles and shingle granules can still accumulate over time. Downspouts are checked to confirm they are not kinked or crushed where they attach to the gutter outlet, and extensions are added to move water farther from the foundation if grading is insufficient.

This service does not include grading changes, French drain installation, or foundation waterproofing, though these measures may be recommended if water pooling persists after gutters are installed. Gutter systems work best when combined with proper roof drainage and site grading, and APT Construction can coordinate these elements as part of a broader exterior project.

Homeowners in Molalla often ask about gutter capacity, maintenance expectations, and how guards perform in wooded settings.

How do I know if my gutters are large enough for my roof?

Standard five-inch residential gutters handle most single-story and two-story homes, but steeper roofs or larger drainage areas may require six-inch gutters to prevent overflow during peak rainfall, which APT Construction determines during the site assessment.

What happens if a gutter guard gets covered with moss?

Most mesh guards allow moss and fine debris to dry and blow off, but in heavily shaded areas, periodic rinsing with a hose may be needed to clear buildup and restore full water flow.

When should downspouts discharge into underground drains instead of splash blocks?

If your lot has limited space between the foundation and the property line, or if the ground slopes back toward the house, underground drains carry water to a lower grade or storm system, preventing it from pooling near the foundation.

Why do some gutters sag even when they look new?

Insufficient hanger spacing or mounting into rotted fascia board allows gutters to pull away under the weight of water, which is why APT Construction inspects and repairs fascia before installing new gutters.

What gutter colors are available to match my home?

Seamless aluminum gutters are formed on site and available in a range of baked enamel colors including white, brown, bronze, and gray, selected to blend with your trim or siding.

APT Construction evaluates your roof, fascia condition, and site drainage to design a gutter system that moves water away from your home effectively and requires minimal maintenance. Contact us to set up a site visit and discuss gutter and guard options for your property.